Add-on Cards
-
MicroworldTXB113 PCIe 3.0-1X TO 6 SATA3 Expansion Card
- 6 AHCI SATA III (6 Gbps) ports through PCI Express x4
- Fully compliant with SATA 3.0 specifications and backward compatible with SATA I/II (1.5/3.0Gbps) drives
- Compliant with PCI Express 3.0 standards
- Port Multiplier Command-based switching supported
- Support SSC for both PCIe and SATA
-
LindyPCI Express 3 PORT USB3.0 Card
- Bus Type: PCI Express (x1)
- Speed: SuperSpeed (5Gbps), High Speed (480Mbps), Full Speed (12Mbps) and Low Speed (1.5Mbps)
- Compliant with USB 3.0 Rev. 1.0 specification
- Compliant with PCIe 2.0 Specification
- Each USB port supplies +5VDC/900mA
- Supports USB 3.0, USB 2.0, and USB 1.1 devices
-
-
SunixSerial High Speed RS-232 Low Profile Card (SER5027H+L)
- Expands single independent RS-232 serial port with communication speeds up to 921.6Kbps.
- High reliability SUN1989 16C950 compatible UART controller on-board.
- Support Microsoft Windows, Linux, and DOS.
-
AorusGC-WBAX200 - intel WiFi 6 AX200 , PCi-E (x1) adapter
- Intel® WIFI 6 AX200 module built-in
- Up to 2400Mbps connection speed (theoretical)
- 802.11abgn+acR2+ax(Pre-Standard) MIMO 2Tx2R
- BLUETOOTH 5.0
- MU-MIMO TX/RX
- Paired with AORUS high performance 2Tx2R antenna
- PCIe x1 interface card
-
Sunix4-port RS-232 High Speed PCI Express Board with Power Output
- Expands four independent RS-232 serial ports with communication speeds up to 921.6Kbps.
- With high reliable SUNIX SUN2410 native PCI Express 16C950 UART controller.
- Designed to meet PCI Express Base Specification Revision 2.0.
- Supports x1, x2, x4, x8, x16 (lane) PCI Express Bus connector keys.
- Provides RS-232 serial ports with +5 or +12 VDC power output via COM 1st or 9th pin.
- On-chip hardware auto flow control to guarantee no data loss.
- Built-in 15KV ESD protection for all serial signals meets IEC1000-4-2 standard.
- Plug-n-Play, I/O address and IRQ assigned by BIOS.
- Certified by CE, FCC, RoHS, and Microsoft WHQL approval.
- Support Microsoft Windows, Linux, and DOS.
-
Orico4 Port USB3.0 PCI-E Card
- Four high speed USB3.0 ports
- Transfer speeds of up to 5gbps
- PCI-e Express Card x1
- Small form factor
- Widely compatible with Windows, Mac and Linux
-
Orico2 Port USB3.0 PCI-E Card
- Upgraded speed, increased extension and superior performance
- Extends 4 USB3.0 ports (2x External & 2x Internal)
- USB3.0 speed is up to 5Gbps
- 4pin power interface
- Eco-friendly and energy-saving
- Stable and abundant power supply
- Operates stably even when all the ports are connected to a 2.5" 2TB hard drive
- It adopts all solid-state capacitor which is made out of conductive polymer
- Long life span and high stability, guarantees a stable power supply
- Dual-edge fold design
-
HPSmart Array E208i-a SR Gen10 Controller
- Form Factor: Type-a Flexible/Modular Controller (does not occupy a PCIe Expansion Slot)
- Supporting 12Gb/s SAS and PCI Express 3.0 x8 link
- RAID 0,1, 5, and 10 and Software Defined Storage solutions
- Mixed Mode (RAID logic drives and HBA physical drives simultaneously)
- 8 Internal Lanes/No Cache
- Storage interface (SAS/SATA)
- VMware Virtual SAN certified
- Legacy and UEFI boot operation
- UEFI System Utilities (storage configuration)
-
VantecM.2 NVMe + M.2 SATA SSD PCIe x4 Adapter
- Support 2 x M.2 interface, One for NVMe SSD and One for SATA SSD
- Primary M.2 for PCIe based (NVMe or AHCI) SSD to PCIe x4 slot
- Secondary M.2 for SATA SSD to the System main board SATA port
- PCIE to M.2 SSD (M-Key), SATA to M.2 SSD (B-Key)
- Support different length M.2 (NGFF) card, 22x42mm, 22x60mm or 22x80mm
- Adapter supports PCI Express v3.0 Specs and compatible with v2.0 / v1.0
- Supports system boards with PCIe x4,x8,x16 slots
- Uses minimum power from PCIe 3.3V for better power management
- Low Profile Bracket included
-
VantecM.2 NVMe SSD PCIe x4 Adapter
- Support M.2 (NGFF) PCIe based (NVMe or AHCI) SSD to PCIe x4 slot
- Support M.2 interface with M key, do not support M+B key
- Support different length M.2 (NGFF) card, 22x42mm, 22x60mm or 22x80mm
- Adapter supports PCI Express v3.0 Specs and compatible with v2.0 / v1.0
- Supports system boards with PCIe x4,x8,x16 slots
- Uses minimum power from PCIe 3.3V for better power management
- Low Profile Bracket included
-
